ITExamDump에서는 전문Juniper JN0-521인증시험을 겨냥한 덤프 즉 문제와 답을 제공합니다.여러분이 처음Juniper JN0-521인증시험준비라면 아주 좋은 덤프입니다. ITExamDump에서 제공되는 덤프는 모두 실제시험과 아주 유사한 덤프들입니다.Juniper JN0-521인증시험패스는 보장합니다. 만약 떨어지셨다면 우리는 덤프비용전액을 환불해드립니다.
ITExamDump는 많은 IT인사들이Juniper인증시험에 참가하고 완벽한JN0-521인증시험자료로 응시하여 안전하게Juniper JN0-521인증시험자격증 취득하게 하는 사이트입니다. Pass4Tes의 자료들은 모두 우리의 전문가들이 연구와 노력 하에 만들어진 것이며.그들은 자기만의 지식과 몇 년간의 연구 경험으로 퍼펙트하게 만들었습니다.우리 덤프들은 품질은 보장하며 갱신 또한 아주 빠릅니다.우리의 덤프는 모두 실제시험과 유사하거나 혹은 같은 문제들임을 약속합니다.ITExamDump는 100% 한번에 꼭 고난의도인Juniper인증JN0-521시험을 패스하여 여러분의 사업에 많은 도움을 드리겠습니다.
성공을 위해 길을 찾고 실패를 위해 구실을 찾지 않는다는 말이 있습니다. Juniper인증 JN0-521시험이 영어로 출제되어 시험패스가 너무 어렵다 혹은 회사다니느라 공부할 시간이 없다는 등등은 모두 공부하기싫은 구실에 불과합니다. ITExamDump의 Juniper인증 JN0-521덤프만 마련하면 실패를 성공으로 바꿀수 있는 기적을 체험할수 있습니다.제일 간단한 방법으로 가장 어려운 문제를 해결해드리는것이ITExamDump의 취지입니다.
시험 번호/코드: JN0-521
시험 이름: Juniper (FWV.Associate (JNCIA-FWV))
당신이 구입하기 전에 시도
일년동안 무료 업데이트
100% 환불보장약속
100% 합격율 보장
Q&A: 119 문항
업데이트: 2014-01-14
많은 시간과 돈이 필요 없습니다. 30분이란 특별학습가이드로 여러분은Juniper JN0-521인증시험을 한번에 통과할 수 있습니다, ITExamDump에서Juniper JN0-521시험자료의 문제와 답이 실제시험의 문제와 답과 아주 비슷한 덤프만 제공합니다.
JN0-521 덤프무료샘플다운로드하기: http://www.itexamdump.com/JN0-521.html
NO.1 You are configuring an interface in the untrust zone with an IP address, telnet enabled, and WebUI
management.
Which sequence of steps must be performed to make the interface operational at the end of the
configuration sequence?
A.Assign the interface to a zone, define the IP address, enable Web and telnet services.
B.Assign the interface to a zone, define the IP address, accept default management services.
C.Assign the interface to a virtual router, define the IP address, enable Web and telnet services.
D.Assign the interface to a zone, define the IP address, define a manage IP address, accept default
management services.
Answer: A
Juniper pdf JN0-521 JN0-521 JN0-521최신덤프 JN0-521
NO.2 In the packet forwarding decision process, how is the second packet handled differently than the first
in a series of allowed interzone packets?
A.The second packet causes an ARP query.
B.The second packet is checked against the policy table.
C.The second packet is forwarded without a sanity check.
D.The second packet is forwarded without checking the route table.
Answer: D
Juniper자격증 JN0-521인증 JN0-521기출문제 JN0-521 JN0-521인증
NO.3 When performing an image upgrade using the CLI, which three locations would be a source for this
image? (Choose three.)
A.FTP server
B.TFTP server
C.internal flash
D.PC local disk
E.Compact Flash Card
Answer: BCE
Juniper기출문제 JN0-521기출문제 JN0-521자료
NO.4 A ScreenOS firewall is running in transparent mode. The firewall receives a packet which has no entry
in its forwarding table.
What will the firewall do?
A.Flood out all ports.
B.Check its route table for interzone destination.
C.Perform a policy lookup to determine the interfaces to which the source address is permitted, and flood
the packet out of those interfaces.
D.Perform a policy lookup to determine the zones to which the source address is permitted, and flood the
packet out the interfaces bound to those zones.
Answer: D
Juniper JN0-521덤프 JN0-521 JN0-521
NO.5 By default, where are changes stored when a save command is issued from the CLI during a
management session?
A.NVRAM
B.internal flash
C.PCMCIA card
D.Compact Flash Card
Answer: B
Juniper최신덤프 JN0-521 JN0-521 JN0-521
NO.6 An operational firewall needs a configuration loaded and executed while it is passing user data.
Which CLI command will perform this process without interrupting traffic?
A.save config from tftp 1.1.7.250 15June06.cfg to flash
B.save config from tftp 1.1.7.250 15June06.cfg to ram
C.save config from tftp 1.1.7.250 15June06.cfg merge
D.save config from tftp 1.1.7.250 15June06.cfg to flash
Answer: C
Juniper시험문제 JN0-521 dump JN0-521시험문제 JN0-521
NO.7 Which statement is correct regarding administrator privileges?
A.Any administrator can change their privileges on an as-needed basis.
B.Administrator privileges can only be established and changed by the root administrator.
C.Administrator privileges can be established and changed by the root and all-privilege administrator.
D.Administrator privileges can only be established by the root and can be changed by the root and
all-privilege administrator.
Answer: B
Juniper최신덤프 JN0-521 JN0-521 JN0-521기출문제
NO.8 Which command would you run to check IPSec Phase 1 active status?
A.get sa
B.get event 427
C.get sa active
D.get ike cookie
Answer: D
Juniper자료 JN0-521 JN0-521 JN0-521 pdf
NO.9 Which ScreenOS WebUI button reorders policies?
A.Shift
B.Move
C.Reorder
D.Transfer
Answer: B
Juniper JN0-521 JN0-521 JN0-521 JN0-521
NO.10 When managing a ScreenOS device using the WebUI and performing an image upgrade, from which
hardware component will the ScreenOS image be loaded?
A.TFTP server
B.PC local disk
C.internal flash
D.Compact Flash Card
Answer: B
Juniper dumps JN0-521자격증 JN0-521자료 JN0-521자료
NO.11 Which command is used when configuring web management on the VLAN1 interface for a client
connected to an e3 interface in the DMZ zone?
A.set int eth3 manage web
B.set zone v1-dmz manage web
C.set int dmz zone manage web
D.set int VLAN1 zone dmz manage web
Answer: B
Juniper최신덤프 JN0-521 JN0-521자격증
NO.12 Click the Exhibit button.
In the exhibit, which two forms of address translation would have generated the output shown? (Choose
two.)
A.MIP
B.NAT-src with no DIP
C.Interface-based translation
D.NAT-src with a DIP, fixed-port disabled
Answer: BC
Juniper JN0-521 JN0-521 JN0-521
NO.13 What is the purpose of the "Permitted IP" address on a ScreenOS device?
A.It defines a list of addresses that are trusted to perform management on the ScreenOS device.
B.It is used in policy rules to determine which user traffic is allowed through the ScreenOS device.
C.It defines which range of addresses that can access devices connected to the ScreenOS device.
D.It is the address that an external device uses to gain management access to a ScreenOS device.
Answer: A
Juniper자격증 JN0-521시험문제 JN0-521시험문제 JN0-521자격증
NO.14 Click the Exhibit button.
In the exhibit, which interface would be used to forward traffic to host 1.1.7.5?
A.e0/1
B.e0/2
C.e0/3
D.e0/4
Answer: C
Juniper덤프 JN0-521최신덤프 JN0-521 dump JN0-521인증
NO.15 Which process describes how an addressed physical interface is moved into a Layer 2 zone?
A.Place the required interface into the VLAN zone.
B.Place the required interface into L2 zones such as V1-Trust, V1-Untrust
C.Remove the interface from the L3 zone such as Trust and place it into a L2 zone such as V1-Trust
D.Remove the address from the interface, remove the interface from the L3 zone, and then place
interface in the L2 zone.
Answer: D
Juniper기출문제 JN0-521 pdf JN0-521기출문제 JN0-521 dump JN0-521 pdf
NO.16 You are looking at the event log of the responding device and it says,
"Rejected an initial Phase 1 packet from an unrecognized peer gateway"
What are three likely reasons for the failure? (Choose three.)
A.The peer ID is misconfigured.
B.The default gateway is missing.
C.The preshare keys are mismatched.
D.The gateway address is misconfigured.
E.The outgoing interface is misconfigured.
Answer: ADE
Juniper JN0-521 JN0-521 JN0-521시험문제 JN0-521 pdf
NO.17 What is the purpose of the VLAN1 interface?
A.It provides policy-based NAT for 802.1Q VLANs.
B.It provides an interface that can be used with 802.1Q VLANs in transparent mode.
C.It provides the ScreenOS device with a routable IP address while operating in route mode.
D.It provides an interface that can be used to remotely manage the ScreenOS device while operating in
transparent mode.
Answer: D
Juniper JN0-521최신덤프 JN0-521 pdf JN0-521 JN0-521덤프
NO.18 What is the purpose of the "Manage-IP" address on a ScreenOS device?
A.It defines a list of addresses that are trusted to perform management on the ScreenOS device.
B.It is used in policy rules to determine which device is allowed to manage the ScreenOS device.
C.It is the address that an external device uses to gain management access to a ScreenOS device.
D.It defines a list of device addresses that can manage the ScreenOS device without being authenticated
prior to session establishment.
Answer: C
Juniper JN0-521덤프 JN0-521
NO.19 What are two benefits of configuring a ScreenOS device in transparent mode? (Choose two.)
A.There is no need to reconfigure the IP addresses of routers or protected servers.
B.There is no need to create MIPs or VIPs for incoming traffic to reach protected servers.
C.Policies are easier to create since you do not have to include source and destination IP addresses.
D.The product can support more VPNs and obtain greater throughput because there is less overhead to
manage.
Answer: AB
Juniper JN0-521기출문제 JN0-521시험문제 JN0-521자료 JN0-521
NO.20 Which type of NAT is performed when you implement interface-based NAT?
A.source IP address translation
B.destination IP address translation
C.source IP and port address translation
D.destination IP and port address translation
Answer: C
Juniper덤프 JN0-521 pdf JN0-521
NO.21 By default, from which hardware component is the startup copy of the ScreenOS loaded?
A.NVRAM
B.TFTP server
C.internal flash
D.PCMCIA card
Answer: C
Juniper자격증 JN0-521덤프 JN0-521 JN0-521덤프 JN0-521인증
NO.22 When configuring a firewall in a critical environment where a local backup configuration is quickly
needed, what should be completed on a periodic basis?
A.Execute exec config rollback.
B.Execute save config to last-known-good.
C.Execute save regularly or create a script that does this.
D.Execute save software from flash to pcmcia .
Answer: B
Juniper자격증 JN0-521 dumps JN0-521 dump JN0-521
NO.23 Telnet management has been enabled on an interface in the untrust zone.
What else should be completed to limit telnet access to the ScreenOS device from trusted management
PCs?
A.Define a permitted IP address.
B.Define a policy from trust to untrust.
C.Define a trusted IP in the address table.
D.Define a manage IP address on this interface.
Answer: A
Juniper JN0-521인증 JN0-521 JN0-521기출문제
NO.24 What will change the root admin password?
A.set admin password
B.set root-admin password
C.set admin password
D.set admin user password
Answer: A
Juniper JN0-521자격증 JN0-521 JN0-521 JN0-521
NO.25 A ScreenOS firewall has the correct interfaces addressed and active. A policy is written allowing
interzone FTP traffic from a directly connected client. But the traffic does not cross the firewall from the
client to the server.
What is the most likely problem with the firewall?
A.The ScreenOS firewall has no physical connection to the FTP server.
B.The ALG option on the ScreenOS firewall has not been enabled for FTP traffic.
C.The ScreenOS firewall does not have a route defined to the FTP servers' subnet.
D.The ScreenOS firewall does not have a route defined to the FTP clients subnet.
Answer: C
Juniper JN0-521인증 JN0-521 JN0-521자격증
NO.26 Which two statements are true in regards to a ScreenOS firewall in transparent mode? (Choose two.)
A.VPNs can terminate to the VLAN1 interface IP address.
B.Static routes must be configured if multiple virtual routers are going to be used.
C.It can be installed in a network without the requirement to reconfigure IP addressing schemes.
D.You must use the console port to manage the device as you cannot manage the device using an
Ethernet port.
Answer: AC
Juniper dumps JN0-521덤프 JN0-521 JN0-521 dump
NO.27 Which statement accurately describes the "config rollback" feature?
A.Once the "config rollback" feature is enabled, it allows the administrator to re-apply a previously saved
configuration file from flash.
B.The "config rollback" feature is enabled by default, it allows the administrator to re-apply a previously
saved configuration file from flash.
C.Once the "config rollback" feature is enabled, it allows the administrator to re-apply a locked
configuration file from a separate area in flash.
D.Once the "config rollback" feature is enabled, it allows the administrator to revert to the prior ScreenOS
image or configuration file in the event an upgrade operation aborts.
Answer: C
Juniper자격증 JN0-521 JN0-521 JN0-521덤프 JN0-521 JN0-521
NO.28 In the command, save config from tftp 1.1.7.250 abcd.cfg merge, which function does the merge
parameter specify?
A.The config file from the TFTP server will replace the configuration in RAM.
B.The config file from the TFTP server will replace the startup configuration file in internal flash.
C.The merge parameter is not valid for TFTP files, it is only valid for configuration files stored in internal
flash.
D.The config file from the TFTP server will be combined with the configuration file in RAM and the
combined result will be saved in internal flash.
Answer: D
Juniper덤프 JN0-521 JN0-521 dumps JN0-521덤프 JN0-521최신덤프
NO.29 When a firewall receives the first packet in a series, what will it immediately do?
A.Check its route table.
B.Check its session table.
C.Determine if traffic is crossing zones.
D.Verify that it is not malformed or a fragment.
Answer: D
Juniper기출문제 JN0-521자료 JN0-521덤프 JN0-521 dumps
NO.30 When changes are made to the running config during a WebUI management session, to what external
hardware component can the changes be saved?
A.FTP server
B.TFTP server
C.PC local disk
D.Compact Flash Card
Answer: C
Juniper JN0-521 JN0-521인증 JN0-521최신덤프 JN0-521인증
ITexamdump의 000-123덤프의 VCE테스트프로그램과 00M-617덤프는 한방에 시험을 패스하도록 도와드립니다. ITexamdump 에서는 최신버전의 000-276시험에 대비한 고품질 덤프와 000-657시험 최신버전덤프를 제공해드립니다. 최고품질 HP2-B103시험자료는 100% 간단하게 시험패스하도록 최선을 다하고 있습니다. IT인증시험패스는 이토록 간단합니다.
댓글 없음:
댓글 쓰기